What the Aluminata 2 Is Designed For
The JPS Labs Aluminata 2 is an interconnect cable built for systems where preserving delicate low-level signals is critical. In a high-end headphone or speaker setup, the cable between your source and amplifier is responsible for passing the full musical signal without adding or subtracting anything. The Aluminata 2 uses specially annealed solid-core Alumiloy conductors with negligible signal loss, each individually insulated with medical-grade Kapton. Its Particle Aluminum Shield (PAS) is optimized for high-resolution audio, aiming to reject noise without interacting with the signal itself.
If you have invested in refined separates, the cable can be the weak link. The Aluminata 2 is designed to act as a clean interface between components, allowing each piece to perform without interference from the connecting cable.
Key Design Details at a Glance
- JPS Labs Aluminata 2 - RCA & XLR Interconnect Cables: Hand-Made in America. Newly designed and specially annealed solid core Alumiloy conductors with negligible signal loss, even in long lengths, each conductor individually insulated with very expensive medical grade Kapton® to exacting standards of thickness and purity, blanketed by a version of the Particle Aluminum Shield (PAS), optimized for the highest resolution audio, with a holistic approach to noise absorption and ultra low impedance. The combination of solid-core Alumiloy conductors and Kapton insulation is unusual at this price point. It means the cable is engineered for low signal loss and consistent performance across different lengths, which is important if you need a longer run between components.

JPS Labs Aluminata 2 - RCA & XLR Interconnect Cables
RCA or XLR: Which Connector to Choose
The Aluminata 2 is available in both RCA and XLR terminations, each in lengths from 0.75 to 3.0 meters. The choice depends entirely on your components:
If your source and amplifier have balanced XLR outputs and inputs, the XLR version is the straightforward choice. Balanced connections can help with noise rejection in systems with long cable runs or multiple electronic devices nearby.
If your gear uses single-ended RCA connections, the RCA version is the correct fit. RCA is common on many DACs and headphone amplifiers, and the Aluminata 2's RCA variant uses the same conductor and shielding design as the XLR version.
There is no performance advantage of one connector over the other in the Aluminata 2's design itself. The cable's internal construction is identical; the termination is the only variable. Choose the connector that matches your components' inputs and outputs.
Compatibility with Your System
The Aluminata 2 is an interconnect cable, not a headphone cable. It connects a source (like a DAC or streamer) to a preamplifier or headphone amplifier. If you are upgrading the cable between your DAC and amp, this is a direct replacement for any standard RCA or XLR interconnect.
For ABYSS headphone systems, the Aluminata 2 fits between your source and amplifier. It does not replace the headphone cable itself (which connects the amp to the headphones). If your goal is to upgrade the entire signal path, you might pair the Aluminata 2 with a headphone cable like the JPS Labs Superconductor HP.
The supplied information confirms that the Aluminata 2 is hand-made in the USA. It does not specify compatibility with specific brands or models beyond general interconnect use. As with any high-end interconnect, verify that your components have the corresponding RCA or XLR jacks and that the cable length suits your physical setup.
What the Supplied Information Does Not Cover
The catalog does not specify the cable's weight, flexibility, or recommended minimum bend radius. It also does not list a warranty period or return policy. If these details matter for your installation, they are not confirmed in the available records.
The Aluminata 2 is designed to reject noise and interference, but no specific shielding effectiveness numbers (like dB reduction at certain frequencies) are provided. The description notes that the Particle Aluminum Shield is optimized for high-resolution audio, but exact performance data is absent.
Finally, the cable is available in lengths from 0.75 to 3.0 meters in both RCA and XLR. If you need a custom length or a different connector type, those options are not listed in the current catalog.
Available Lengths and Connectors
- JPS Labs Aluminata 2 - RCA & XLR Interconnect Cables: Available in 0.75, 1.0, 1.5, 2.0, 2.5, and 3.0 meter lengths, with RCA or XLR connectors. The range of lengths gives you flexibility for different rack or desk setups. If your components are close together, the 0.75m option is available; for longer runs, up to 3.0m is offered.

